The Goodman GSX14 Air Conditioner uses the chlorine-free refrigerant R-410A and features operating sound levels that are among the lowest in the heating and cooling industry. With its 14 SEER rating, the GSX14 will help reduce energy consumption throughout the life of the system.

Standard Features:

• Energy-efficient compressor
• Factory-installed filter drier
• Copper tube/aluminum fin coil
• Service valves with sweat connections and easy-access gauge ports
• Contactor with lug connection
• Ground lug connection
• AHRI Certified
• ETL Listed

Description

Increase the comfort in your home with the Goodman AWUF190516 1.5 ton, wall-mounted air handler. This model from the AWUF series is specifically designed for heat pump and cooling applications. It features a check flowrater and a multi-speed ECM motor, which allows air volume variation for cooling and heating. This air handler comes with a wall-hanging bracket, which ensures fast and easy installation.

The Goodman AWUF190516 is intended to provide 18,000 BTU cooling capacity. Also, it is equipped with sequence-controlled, rust-resistant nickel chromium heating elements, which provide an electric heat capability of 5 kW. The air handler uses eco-friendly R-22 or chlorine-free R-410A refrigerants. This unit features a fully insulated, galvanized-steel cabinet, which ensures lengthier lifespan. Enjoy efficient performance of the Goodman AWUF air handlers.


Features

• Equipped with a Check Flowrater for cooling-only and heat pump operation
• Direct-drive, multi-speed motors allows air volume variation for heating/cooling
• Multi-speed ECM: AWUF19, 25, 31, 32, 37
• Multi-speed PSC motor: AWUF18, 24, 30, 36
• Sequence-controlled, rust-resistant nickel chromium heating elements of 3, 5, 8, and 10 kW
• Aluminum tubing coils on all models
• AHRI Certified; ETL Listed
• Factory-installed pull-type disconnect
• Thermoplastic drain pan with bottom primary and secondary drain connections
• Built-in filter rack (filter included)
• Large chassis (2 1/2 - and 3-ton units) – front return only
• Small chassis (1 1/2 - and 2-ton units) – front or bottom return
• Wall-hanging bracket provided

Description

The Goodman HKSX05XC is an electric heat kit. It comes from the HKS line, which is intended for use with Goodman air handlers. This model uses rust-resistant nickel chromium heating elements and has 5 kW nominal heating.

This Goodman heat kit features sequences for better temperature control. It has multiple branch circuit capability and has been completely assembled and tested so our customers know they are good to go. Plus, Goodman electronic heat kits are known for being easy to install and a plug-in wiring harness makes it simple to fit into the air handler.

Features

• Designed for higher airflow requirements
• Available with or without circuit breakers
• Ship without the electric heater cover plate installed but the heater cover will be included with the literature packet if needed in no heat applications
• For Use With: All ARPT, ARUF & AVPTC AH's

• Wt. Lbs.: 9
• Breaker: No
• Nom. kW: 5.0
• Shipping Weight: 3.05
• Shipping Width: 8.40
• Shipping Length: 14.70
• Shipping Height: 9.60
• Voltage: 208/240V

Description

A specially formulated super-hydrophobic (water repelling) product in a convenient aerosol package for field service. The non-conductive formula has numerous applications in the management of water on non-food, non-potable water surfaces for the HVAC/R trade; surfaces that are not exposed to ongoing abrasion (hand and foot traffic).

• Slows ice formation on refrigeration coils/cold plates

• Provides added corrosion resistance to coils

• Improves corrosion resistance to system components. Examples include circuit boards, filter-driers, flow control valves, equipment covering, etc.

• Provides added corrosion protection of solder connections on low voltage circuit boards

• Self-cleaning properties reduce rate of grime on outdoor coils

• Reduces rate of bacterial growth on non-food, non-potable water surfaces

• Improves water dispersion in condensate pans

• Many other applications!

• Nominal Capacity Range: 1 1/2 Tons
• Heater Kit: 5 kW
• Electrical: 208/240V, 1 Phase, 60 Hz
• Refrigerant Compatibility: R-410A, R-22
• Cooling (Btu/h): 18,000
• Electric Heat (kW): 5
• Diameter: 10"
• Width: 6"
• Liquid: 3/8"
• Suction: 5/8"
• Coil Drain Connect (FPT): 3/4"
• Voltage: 230/208V
• Min Circuit Ampacity (230V): 28.3
• Min Circuit Ampacity (208V): 24.9
• Max. Overcurrent Device (240V): 30
• Max. Overcurrent Device (208V): 25
• Minimum VAC: 197
• Maximum VAC: 253
• Full Load Amps (FLA): 2.6
• Horsepower (HP): 1/3

Directions

This product must be used in accordance to the following directions by HVACR professionals only.

1. Disconnect all power to the equipment before use. Do not spray near sparks, heat or open flame. Discontinue the use of power tools during use. Do not smoke while applying product.
2. Shake well before use. Use outdoors or in a well-ventilated area. Keep area ventilated until fumes are gone. Avoid breathing of fumes during application.
3. Ensure surface is clean and mostly to fully dry before applying. After a coil cleaning, the surface needs to be blown dry with an inert gas to remove excess moisture from the surface before applying Nu-Shield.
4. From a distance of 6-12 inches, spray a light coat on the surface, but no more beyond it being visibly wet. In other words, ‘Wet It and Forget It’. Contents in the canister will cover approximately 100 square feet. Depending on ambient conditions, allow a minimum of 20 minutes for Nu-Shield to dry on surface. Ensure surface appears visually dry and fumes are gone from the area before turning on power to equipment.

Note: Product needs to be applied after each coil cleaning. For best results, especially in corrosive environments, the product should be reapplied annually.

10 Year All Parts Warranty

SHIPPING DETAILS

Mostly All Of Our Products Are Shipped Same Or Next Day

Your product will be mostly shipped using Freight Company such as SAIA, ESTES, Old Dominion, FEDEX or UPS and will be delivered in 1-5 business days depending upon your geographical location from our warehouses. We ship products from warehouses in NY, NJ, FL, CA,AZ, TX And MO. Mostly if you are close to our warehouses, you should receive the Product in 1-3 business days. We will email you your tracking number soon as its shipped out or you can log into your account on our website by using your email address and password you created at the time of placing order to check all the shipment and product details.
Please remember we only ship to 48 states within United States. Due to expensive shipment fee we do not ship to Hawaii & Alaska. We do not ship to Canada, Puerto Rico, Jamaica and other countries due to custom issues.

Though above shipment and delivery process is what we normally practice, under unforseen circumstances they cannot be guaranteed at all times. But we do our best and mostly succeed to ship the product either same or the next day.

Overnight Shipping Details (if required)

We can ship overnight or by Second Day Air. But beacuse these are air conditioners and the package weighs more than 90 pounds usually, shipping overnight can result in the package being mishandled and delivered damaged. Plus it cost anywhere from $180-$850 more than regular shipping depending upon your location from our warehouse. Feel free to email us with such enquiries.